Listar por título
Mostrando ítems 1878-1897 de 2282
-
Reduction and mitigation of foreign matter observed in product ABC
(Polytechnic University of Puerto Rico, 2020)During the past three years, a manufacturing company for medical devices on the west side of Puerto Rico has been in the need of evaluating and mitigating the causes behind an increase in complaint incidents reported due ... -
Reduction in Dissolution Test Results Variability of A/B Capsule Product
(Polytechnic University of Puerto Rico, 2013)Since the origins of the agency, the Food and Drugs Administration (FDA), a scientific, regulatory, and public health agency had been dedicated to consumer protection. The FDA, provides standardized regulations and ... -
Reduction in Dye Test Failures Incidence for Cartridges Manufacturing Process in the Medical Device Industry
(Polytechnic University of Puerto Rico, 2023)The medical device industry is known to be regulated by regulatory agencies across the world. Every year, a significant number of Non Conformances (NCs) and Corrective Actions Preventive Actions (CAPA’s) are generated to ... -
Reduction in lead times of manufacturing Product X
(Polytechnic University of Puerto Rico, 2020)The project takes place in an Aerospace Company in Puerto Rico. The purpose of it was to reduce the lead times of a specific product called Product X, the product that will benefit the company the most. Qualitative ... -
Reduction in Waste of Raw Material Generation N and D of the Manufacturing Processes in a Medical Device Industry
(Polytechnic University of Puerto Rico, 2015)This article discusses how the industry of Medical Devices handles the reduction of waste in manufacturing processes. Companies have money losses, that can be reduce with an optimization of the manufacturing processes. ... -
Reduction in Waste of Raw Material Generation N and D of the Manufacturing Processes in a Medical Device Industry
(Polytechnic University of Puerto Rico, 2016)This article discusses how the industry of Medical Devices handles the reduction of waste in manufacturing processes. Companies have money losses, that can be reduce with an optimization of the manufacturing processes. ... -
Reduction of Cosmetic Defects Due to Criteria Misalignment at a Medical Device Manufacturing Line Using DMAIC Methodology
(2013)For the last few years, the economy of Puerto Rico has been negatively affected, increasing the operational cost of the industries in the Island. The Pharma / Medical Device industry is not excluded of this situation. ... -
Reduction of downtime through the design of TPM and the implementation of some techniques of SMED system at high speed packaging lines
(Polytechnic University of Puerto Rico, 1996-06)This project was developed at a pharmaceutical facility located in the eastern area of Puerto Rico. The company manufactures oral contraceptives and analgesics. In the analgesic branch a new product is being introduced, ... -
Reduction of Extensive Construction Costs & Lead Times of Single-Family Homes in Florida due to Covid-19
(Polytechnic University of Puerto Rico, 2022)The timely completion of single-family homes in Florida was significantly affected by the outbreak of COVID-19 due to increased prices of materials, services, and lead time. Supply chain disruption and inefficient project ... -
Reduction of Finished Goods Inventory in Masterpact: Breakers and Cradles Lines
(Polytechnic University of Puerto Rico, 2017)At the moment, there is no trigger for internal demand or set capacity to build internal orders of breakers or cradles. This results in misuse capacity and high inventory levels of MPACT finish goods. The purpose of the ... -
Reduction of Human Errors Investigations Related to Documentation in Manufacturing Areas
(Polytechnic University of Puerto Rico, 2019)The human error has become an issue in the pharmaceutical companies. The biggest challenges throughout times have been detection and prevention of the human errors. An example of this situation occurred in BMS, Manati ... -
Reduction of Input to Output Process Time for CFD Processes
(Polytechnic University of Puerto Rico, 2016)The Aerodynamics Department of the company Infotech Aerospace Services had been experiencing large time delays in one of the processes due to a lack of resources, in this case trained personnel which could process the ... -
Reduction of inventory discrepancies due incorrect bill of material in an electrical manufacturer
(Universidad Politécnica de Puerto Rico, 2020)In the company EM, during the last inventory (2020), a lost cost of over US$100,000 was calculated due to incorrect bill of material or discrepancies related to deviations not implemented. This paper focuses on finding the ... -
Reduction of Lighting Energy Consumption by 25% Site Wide
(Polytechnic University of Puerto Rico, 2019)The lighting energy consumption is typically overlooked at Department of Defense facilities because, if it works and provides sufficient lighting, no one complains. The key to achieving energy savings through lighting, is ... -
Reduction of Review and Approval Process for Manufacturing Procedures
(Polytechnic University of Puerto Rico, 2015)Long waiting times for the review and approval process in the Manufacturing Department affects the batch. The main causes of this problem are the missing signature, dates, comments, steps not executed properly, and formula ... -
Reduction of Scrap in Manufacturing Line B-1 Using Six Sigma Manufacturing Methodology
(Polytechnic University of Puerto Rico, 2012)Abstract - In this research, the focus was in a manufacturing production line of receptacles assembly. The receptacles are the finish good of this production line. In this process the receptacle is build completely starting ... -
Reduction of the Vacation Ownership Cancellations in a Hospitality Industry
(Polytechnic University of Puerto Rico, 2014)Quality loyalty is what all enterprise aims to have with every customer. Hotel chains compete to have the best deals for less. In order to make things different from others, new implementations have revolutionized the ... -
Reduction of Time in a Manufacturing Process for a Pharmaceutical Company Located in Puerto Rico
(Polytechnic University of Puerto Rico, 2012)Abstract - The project is developed in a chemical plant of a pharmaceutical company in Puerto Rico. In 2011 the company had an increase in market demand of the active ingredient of one product. To ensure the profit plan, ... -
Reduction of Turnover in Company Z
(Polytechnic University of Puerto Rico, 2022)Company turnover is a problem that affects profits for most companies around the US. The main causes of this problem are the lack of employee recognition, poor onboarding experience and employees not being compensated ... -
Reestructuración y desarrollo de instalaciones en desuso utilizando la Metodología de Ruta Critica
(Polytechnic University of Puerto Rico, 2021)Este proyecto se desarrolló con el objetivo de implementar la metodología de Ruta Crítica para la construcción de salón de entretenimiento y áreas deportivas en la compañía Pratt and Whitney Puerto Rico localizada en ...